Five Coating Services · Lincoln, NE

Metal Roof Coating Services in Lincoln

Five Coating Systems Matched to Panel, Slope, and Surface

We provide metal roof coating services in Lincoln for steel panels, low slopes, pitched runs, foam roofs, and asphalt shingles on commercial buildings.

Get A Free Ballpark Estimate Call Us

Roofer walking a metal roof with a building owner during an inspection

Our Metal Roof Coating Services in Lincoln

Each of our metal roof coating services in Lincoln starts from the same roof walk, then branches into the system that fits your panels and slope.

Roofer priming rust and sealing a metal panel seam before coating

Main service

Commercial Metal Roof Coating

Full restoration for exposed-fastener and standing-seam roofs on shops, plants, and warehouses. The roof is washed, rust is treated, stripped screws are replaced with oversized fasteners, laps are sealed, and a topcoat is built to the specified thickness.

Best on solid steel with surface rust
Covers fastener rows and side laps
Check first: framing and rust-through

Commercial metal roof coating

Low slopes

Silicone Roof Coating

A moisture-cured coating for low-pitch roofs where puddles linger after rain. Drains are cleared, primer goes on where the substrate calls for it, seams are sealed, and the silicone is checked with a film gauge as it goes on.

Best where water sits for a day or two
Holds up under ponding and sun
Check first: drains and deck sag

Silicone roof coating

Roofer rolling acrylic coating onto sloped metal roof panels

Pitched panels

Acrylic Roof Coating

A water-based, reflective coating for sloped metal that drains quickly. It goes on in warm, dry weather over primed steel and sealed fasteners, and later recoats stay in the same acrylic system.

Best on panels that dry fast
Light finish reflects summer sun
Check first: low spots near eaves

Acrylic roof coating

Crew spraying roofing foam across a flat commercial roof

Insulation and slope

Spray Foam Roofing

Closed-cell foam sprayed over the existing roof seals every fastener and lap in one layer, adds insulation with each inch, and can build slope toward drains. A topcoat keeps sunlight off the foam.

Best on cold shops and flat decks
One layer over hundreds of screws
Check first: wet insulation

Spray foam roofing

Roofer applying coating to an asphalt shingle roof on a commercial building

Asphalt shingles

Shingle Roof Coating

A coating made for asphalt shingles on offices, churches, and clinics. It goes on only when the shingles still lie flat and hold their granules, after missing tabs are replaced and loose shingles secured.

Best on faded, flat shingles
Keeps shingles and underlayment in place
Check first: curl and brittleness

Shingle roof coating

Which System Fits Which Roof

A quick comparison of the five systems on the factors that decide most Lincoln jobs.

System	Best Substrate	Standing Water	Coats	Recoat Path
Commercial metal coating	Painted or rusted steel panels	Depends on the topcoat chosen	Primer, detail coat, topcoat	Same system over a clean film
Silicone	Low-slope metal, foam, older coatings	Tolerates ponding	One or two	Silicone only
Acrylic	Sloped metal with good drainage	Softens under ponding	Two or more	Acrylic over acrylic
Spray foam	Metal, flat decks, older roofs	Handled by the topcoat	Foam plus topcoat	Topcoat recoat
Shingle coating	Flat-lying asphalt shingles	Sloped roofs only	Per product listing	Spot repair and recoat

Many Lincoln buildings mix two of these systems: silicone on the low sections, acrylic or a metal coating on the steep runs, and shingle coating on an office wing. The roof walk maps where each one goes.

Not Sure Which System Your Roof Needs?

Tell us the roof type, the slope, and what you see on the panels or inside the building when it rains. We can point you toward the right system before the walk.

Call Us

How Every Coating Service Starts

Whatever system goes on, the work runs in the same order, and the roof walk decides the details.

Inspect Your Roof
We walk the whole roof, note the substrate, slope, ponding areas, fastener and lap condition, and take moisture readings so the system choice rests on what is actually there.
Match The System
Slope, standing water, insulation needs, and future upkeep point to one of the five systems, or a mix of two on different roof sections.
Prepare The Surface
Cleaning, rust treatment, fastener and lap repairs, drain work, or wet-area removal happen before any coating or foam goes down.
Apply And Check
The system goes on at its specified thickness, with wet film checks during application and extra passes at seams, laps, and low spots.
Walk The Finished Roof
A final walk checks curbs, edges, laps, and drains, touches up thin areas, and records the system and thickness applied for your maintenance file.

Get A Free Estimate

Questions About Choosing a Coating Service

What Lincoln owners ask when comparing coating systems for a metal, flat, foam, or shingle roof.

Crew spraying coating across a commercial metal roof in Lincoln, NE

Still Weighing Two Systems?

Call and describe the roof. We will tell you which systems are worth comparing.

Call Us

Which metal roof coating service fits my building?

Slope and standing water decide most of it. Sloped steel that drains fast usually takes acrylic or a metal coating system, low slopes that hold water lean toward silicone, cold buildings or flat decks often suit foam, and asphalt roofs need a shingle coating. The walk confirms it.

Can two systems go on one roof?

Yes. Many buildings have a steep section and a flat one, so silicone can cover the low areas while acrylic or a metal coating goes on the pitched runs. The systems are chosen so they meet cleanly at the transition.

Do all five services use the same planning range?

Coating-level work across these services is planned at about $2.50 to $4.00 per square foot, with replacement-level work at about $5 to $8. Prep, coats, roof size, and access set where your job lands.

Is foam a coating or a new roof?

Foam sits in between. It is sprayed over the existing roof like a coating, but it adds insulation and can build slope, and it always needs its own protective topcoat. On metal shops it often replaces a full re-roof.

How do I know if my roof is past coating?

Rust-through across large areas, sagging framing, widespread wet insulation, and curling or brittle shingles are the usual signs. When we see them, we say so plainly instead of recommending a coating.

Can you coat over a roof that already has an old coating?

Often, once the old coating is tested. If it still adheres and is compatible, it is cleaned and coated over, with acrylic over acrylic and silicone over silicone the common pairs. Peeling or incompatible coating is removed in the affected areas before anything new goes on.

Book Metal Roof Coating Services in Lincoln

Get a ballpark range for your roof, or call and tell us what kind of roof you have.